Skip to main content
Power Generation Piping

Alloy bends, heat treated at the same facility.

Carbon steel, stainless steel and alloy piping bends for steam, gas-turbine and hydro projects, with stress relieving at our facility and full material traceability.

Pipe on the furnace charge car before post-bend heat treatment at Benpro's Calgary shop

Benpro fabricates piping bends for power generation projects across Canada and the United States: carbon steel, low-alloy grades including P11, P22 and P91, stainless steel, and nickel alloys such as Inconel 625 and Incoloy 825. Induction bending to 36" outside diameter, with stress relieving to 680 °C in our own furnace where the grade and the code allow. ASME B31.1 power piping work is a routine offering. Established 1986.

Written for project leaders

A missed heat treatment cycle is not recoverable.

Power piping does not forgive process errors the way some work does. If you are leading a steam-cycle replacement, a hydro penstock package or a balance-of-plant scope, you need a fabricator whose heat treatment is not a subcontract with somebody else's queue attached.

Ours is a stress-relieving furnace at the same facility as the induction benders, temperature up to 680 °C and measuring 5.4 by 3 by 3.6 metres. Where a grade calls for a cycle above that range, we will say so at quote stage and the work goes out to a specialist. For grades within our range, the bend does not get on a truck between forming and treatment, and the cycle records go into the same documentation package as the bend report and the mill test report.

Induction

Up to 36" OD · 10 m radius · 180°

Low-alloy grades

P11 · P22 · P91

Nickel alloys

Inconel 625 · Incoloy 825 and adjacent grades

Stainless

304 · 316 and duplex

Heat treatment

In-house, to 680 °C · 5.4 × 3 × 3.6 m furnace

Code

ASME B31.1 · ASME B16.49

Machining

CNC weld bevels, transitions and Victaulic grooves

The pressure points

What power piping teams worry about.

Traceability on alloy material

P91 in particular is unforgiving about chain of custody and thermal history. Material traceability runs through our shop on the job number and the heat number, and the records ship with the steel.

Getting the thermal cycle right

Cycle requirements come from the material and the governing code, not from a standing recipe. Send us the grade and the specification and we will confirm the cycle before we run it, rather than after.

Outage windows

Bends for a spring or fall outage get ordered in the quiet months and have to land on time. Tell us the outage date with the enquiry and we will tell you whether we can hold it.

Power generation FAQ

Questions from piping engineers.

Do you bend P11, P22 and P91 alloy steel?

Yes. These grades are confirmed bending work for us. Their heat treatment requirements depend on the code and the fabrication history, and where a cycle sits above our furnace range we will say so at quote stage and arrange it with a specialist.

Is post-bend heat treatment carried out in-house?

Our furnace works up to 680 °C and measures 5.4 m long by 3 m wide by 3.6 m high, at the same facility as the induction benders, so there is no shipping leg between forming and treatment. Grades needing a cycle above that range are sent to a specialist, and we will tell you which applies when we quote.

Do you work to ASME B31.1?

Yes. ASME B31.1 power piping is a routine offering, alongside ASME B16.49 for factory-made induction bends.

Do you bend Inconel and other nickel alloys?

Yes. Inconel 625, Incoloy 825 and adjacent nickel alloys have run through our shop.

What is the largest diameter you can bend in alloy?

Induction bending goes to 36" outside diameter across carbon steel, stainless steel and alloys. Achievable radius depends on the grade and wall, so send the details and we will confirm.

Do you provide full MTR and material traceability?

Yes. Mill test reports, bend reports, heat treatment cycle records and lab results are assembled as the job runs and ship with the steel.

Can you work to an outage schedule?

We work with outage dates and will tell you at quote stage whether a date is achievable. Because bending, heat treatment, blasting, coating and machining all happen at one facility, our schedule does not depend on anyone else's queue.

Power generation piping

Grade, geometry, cycle, date.

Send those four and we will respond within one business day.

ASME B31.1 · B16.49
P11 · P22 · P91
Inconel 625 · Incoloy 825
304 · 316 · duplex
680 °C furnace in-house